Tab Content
  • LAR-308's Avatar
    09-09-2019, 12:10 PM
    LAR-308 replied to a thread Frank & Billy engineering in Jeep
    Thanks, I have to regroup and use larger hubs and spindles. I was told about a set of 19 spline hubs that I now know are made of unobtainium. So...
    19 replies | 0 view(s)
  • LAR-308's Avatar
    09-03-2019, 09:34 PM
    LAR-308 replied to a thread Frank & Billy engineering in Jeep
    Thanks. The concern with the spindle bearing is supporting the shaft. some hubs have a thorington bearing, while others only have a bushing on the...
    19 replies | 0 view(s)
  • LAR-308's Avatar
    09-01-2019, 02:09 PM
    LAR-308 replied to a thread Frank & Billy engineering in Jeep
    I'm also debating to run a spindle support bearing to support the weight of the axle. Without it the hub will have to support the weight. With the...
    19 replies | 0 view(s)
  • LAR-308's Avatar
    09-01-2019, 02:00 PM
    LAR-308 replied to a thread Frank & Billy engineering in Jeep
    Ok, So one of the things I wanted in this build is to be able to flat tow it. I've been thinking of a full floating kit. Hopefully it be strong...
    19 replies | 0 view(s)
  • LAR-308's Avatar
    08-22-2019, 08:09 PM
    LAR-308 replied to a thread Frank & Billy engineering in Jeep
    thrashed for 3 hours, tadaa...
    19 replies | 0 view(s)
  • LAR-308's Avatar
    08-22-2019, 04:36 PM
    LAR-308 replied to a thread Frank & Billy engineering in Jeep
    I keep leaning towards 31's on stockish springs. or possibly removing half the spring stack for a better ride. But with the fiberglass body the...
    19 replies | 0 view(s)
  • LAR-308's Avatar
    08-21-2019, 06:45 PM
    LAR-308 replied to a thread Frank & Billy engineering in Jeep
    I'd like to thank yall for reading this. This whole JOB thing just gets in the way of planning fun. If I were rich I wouldn't put up with that...
    19 replies | 0 view(s)
  • LAR-308's Avatar
    08-21-2019, 03:13 PM
    LAR-308 replied to a thread Frank & Billy engineering in Jeep
    I got interrupted I'll finish post later
    19 replies | 0 view(s)
  • LAR-308's Avatar
    08-21-2019, 03:04 PM
    LAR-308 replied to a thread Frank & Billy engineering in Jeep
    The guy I got it from said the 304 run about 2 years ago, which means 4-5, and it smoked badly. I have a 350 chevy on the stand. the 3 speed is...
    19 replies | 0 view(s)
  • LAR-308's Avatar
    08-21-2019, 07:05 AM
    LAR-308 replied to a thread Frank & Billy engineering in Jeep
    So, keeping in mind that I started accumulating the jeep stuff about a year ago, this may not be as entertaining as you think. I thought about what...
    19 replies | 0 view(s)
  • LAR-308's Avatar
    08-19-2019, 07:33 PM
    LAR-308 started a thread Frank & Billy engineering in Jeep
    Ok, boy's and girls, I'm stealing from Cory. I also want a mild fairly stock trail rig. My neighbor was building a garage and I felt obligated...
    19 replies | 0 view(s)
  • LAR-308's Avatar
    08-19-2019, 10:17 AM
    LAR-308 replied to a thread this is a test in Testing
    Yes Pipe, I'll try to start the build thread tonight, with pics. Ron
    5 replies | 0 view(s)
  • LAR-308's Avatar
    08-16-2019, 10:33 AM
    LAR-308 replied to a thread this is a test in Testing
    I didn't buy it, I just get to work on it. It's a 74 pinz-gauer, swiss-Austria made. A blast to drive. I did the test pic upload so I can start a...
    5 replies | 0 view(s)
No More Results
About LAR-308

Basic Information

About LAR-308
Make/Model/Year:
1990 jeep wrangler
Engine / Modifications:
350 sbc
Transmission / Transfer Case:
AX15/231/SYE
Front axle (gears, locker/posi, etc.):
Dana 44, 5.13's,detroit locker, 4340 shafts, 1ton tie rods
Rear axle (gears, locker/posi, etc.):
Dana 44, 5.13's, detroit locker, 4340 shafts
Suspension (lift, shocks, etc.):
3.5 super lift, 1"body, 1/2 boom shackles
Tires and Wheels (size, make, etc.):
35" MTR's
Winch:
Warn 8000
Bumpers, nerf bars, skidplates, etc.:
Home made
Location:
Newark
Interests:
Jeep, Laguna, Golf
Occupation:
ASE Master Auto Tech

Signature


1990 YJ, 350 sbc, AX15/231, Tom Woods SYE & shaft, Dana 44's F&R, 5.13's, detroit lockers, 3.5" springs, 1"bl, 1/2" boom shackles, 35" MTR's, Warn 8274, overland bound member #3644

Statistics


Total Posts
Total Posts
340
Posts Per Day
0.12
Last Post
Frank & Billy engineering 09-09-2019 12:10 PM
General Information
Last Activity
Yesterday 02:44 PM
Join Date
03-30-2012
Referrals
1

3 Friends

  1. OSUMBA OSUMBA is offline

    Junior Member

    OSUMBA
  2. R&B Jeeps R&B Jeeps is offline

    Junior Member

    R&B Jeeps
  3. Tennessee Tennessee is offline

    Member

    Tennessee
Showing Friends 1 to 3 of 3